DGCA Technical General: Fuel, Mixture & Carburation Questions
78 exam-style Fuel, Mixture & Carburation questions for the DGCA Technical Generalpaper (CPL & ATPL). The first 12 are free below with answers and explanations — sign up free to practise all of them with progress tracking.
- Q1
If the specific gravity of a fuel is known to be 0.7, 100 Imperial Gallons of it will weigh:
- A700 Ib
- B70 Ib
- C7000 Ib
- D7,100 Ib
Show answer
Correct answer: A. 700 Ib
This Explanation is Coming Soon
- Q2
In a modern carburettor, mixture is controlled via
- A Airflow
- B Airflow, fuel flow and temperature
- C Fuel flow
- D Airflow and fuel flow
Show answer
Correct answer: C. Fuel flow
In a modern carburettor the pilot's mixture control adjusts the quantity of fuel metered into the fixed induction airflow, so mixture is set by controlling fuel flow. Leaning at altitude simply reduces the fuel delivered for the air being drawn in.
- Q3
246.When an engine is fitted with a fuel injection system:
- AIt does not require priming.
- BPriming fuel originates from the excess supplied from the engine driven pump
- CA separate priming system is not requirede
Show answer
Correct answer: C. A separate priming system is not requirede
A fuel injection system delivers metered fuel directly to the induction ports or cylinders, so operating the boost pump with the mixture set rich charges the lines and primes the engine through the injectors themselves. No separate priming system is therefore required, although the engine still needs priming fuel for a cold start.
- Q4
The method of priming an engine not fitted with a priming pump is to:
- APump the throttle several times.
- BTurn the engine over several times on the starter-motor before selecting the ignition on.
- CPosition the throttle lever midway between open and close.
Show answer
Correct answer: A. Pump the throttle several times.
Pumping the throttle several times operates the carburettor's accelerator pump, which squirts raw fuel into the induction system and enriches the mixture for starting. This substitutes for a priming pump on engines not fitted with one, though it carries an increased risk of fire in the induction system if overdone.
- Q5
Weakening the mixture below the best fuel/air ratio will cause the engine power to:
- ADecrease.
- BIncrease initially, but decrease below take off power.
- CIncrease.
- DBe unaffected by altitude increase.
Show answer
Correct answer: A. Decrease.
This Explanation is Coming Soon
- Q6
What does ‘octane rating’ when applied to AVGAS refer to:-
- AThe waxing point of the fuel
- BThe ability of the fuel to disperse water
- C The anti-knock value of the fuel
- D The volatility of the fuel
Show answer
Correct answer: C. The anti-knock value of the fuel
For AVGAS the octane (performance) rating expresses the fuel's anti-knock quality, that is its resistance to detonation under compression and heat. A higher rating means the fuel can withstand higher cylinder pressures without knocking.
- Q7
The pressure in the induction manifold of a normally aspirated engine:
- ARemains constant as the throttle is opened.
- BDecreases as the throttle is opened.
- CInitially increases as the throttle is opened but decreases after approximately the half open position.
- DIncreases as the throttle is opened.
Show answer
Correct answer: D. Increases as the throttle is opened.
This Explanation is Coming Soon
- Q8
The engine driven fuel pump supplies:
- AThe exact amount of fuel required for all running conditions.
- BMore fuel than is required by the engine; the excess fuel is recycled.
- CThe exact amount of fuel required for all running and starting conditions.
- DMore fuel than is required by the engine, the excess being used as priming fuel.
Show answer
Correct answer: B. More fuel than is required by the engine; the excess fuel is recycled.
This Explanation is Coming Soon
- Q9
The EGT indication on a piston engine is used
- A To control the cooling air shutters
- B To monitor the oil temperature
- C To assist the pilot to adjust the fuel mixture
- DTo indicate cylinder head temperature
Show answer
Correct answer: C. To assist the pilot to adjust the fuel mixture
On a piston engine the exhaust gas temperature indication is used to help the pilot lean the mixture, since peak EGT identifies the chemically correct fuel-air ratio from which the mixture can be set for best power or best economy.
- Q10
A fuel grade which is used in typical aircraft engines is:
- AD.T.D. 585/100
- BD.E.R.D. 2479
- CAVGAS 100
- DD.E.R.D. 2484
Show answer
Correct answer: C. AVGAS 100
This Explanation is Coming Soon
- Q11
In a normally aspirated piston engine carburettor icing can occur:
- A Between 0oC and –10oC
- B At more than + 10oC
- C Only at less than + 10oC if there is visible moisture
- D Only above 5000 ft
Show answer
Correct answer: C. Only at less than + 10oC if there is visible moisture
Carburettor icing forms when the pressure drop and fuel vaporisation in the venturi cool the induction air below freezing, so it can occur in ambient conditions at or below about +10°C provided there is visible moisture or high humidity. It is not confined to sub-zero air or to high altitude.
- Q12
For maximum endurance the mixture control should be set to:
- AWeak.
- BThe chemically correct state.
- CBetween rich and weak.
- DRich.
Show answer
Correct answer: A. Weak.
This Explanation is Coming Soon
66 more Fuel, Mixture & Carburation questions in the full bank
Create a free account to practise every Fuel, Mixture & Carburation question with instant scoring, chapter tests, previous DGCA papers and full-length mock exams.
Start practising free